View AUIRFB8409_6238206.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

hexfet power mosfet s d g absolute maximum ratings stresses beyond those listed under ?absolute maximum ratings? may cause permanent damage to the device. these are stress rati ngs only; and functional operation of the device at these or any other condition beyond those indicated in the specifications is not implied. exposure to absolute- maximum-rated conditions for extended periods may affect device reliability. the thermal resistance and power dissipation ratin gs are measured under board mounted and still air conditions. ambient temperature (t a ) is 25c, unless otherwise specified. hexfet ? is a registered trademark of international rectifier. * qualification standards can be found at http://www.irf.com/ description specifically designed for automotive applications, this hexfet? power mosfet utilizes the latest processing techniques to achieve extremely low on-resistance per silicon area. additional features of this design are a 175c junction operating temperature, fast switching speed and improved repetitive avalanche rating. these features combine to make this design an extremely efficient and reliable device for use in automotive applications and wide variety of other applications. features advanced process technology new ultra low on-resistance 175c operating temperature fast switching repetitive avalanche allowed up to tjmax lead-free, rohs compliant automotive qualified * applications electric power steering (eps) battery switch start/stop micro hybrid heavy loads dc-dc applications gds gate drain source d s g d 2 pak auirfs8409 s d g d to-262 auirfsl8409 to-220ab AUIRFB8409 s d g d v dss 40v r ds(on) (smd) typ. 0.97m ? max. 1.2m ? i d (silicon limited) 409a i d (package limited) 195a symbol parameter units i d @ t c = 25c continuous drain current, v gs @ 10v (silicon limited) i d @ t c = 100c continuous drain current, v gs @ 10v (silicon limited) i d @ t c = 25c continuous drain current, v gs @ 10v (package limited) i dm pulsed drain current p d @t c = 25c maximum power dissipation w linear derating factor w/c v gs gate-to-source voltage v e as single pulse avalanche energy (thermally limited) e as ( tested ) single pulse avalanche energy tested value i ar avalanche current a e ar repetitive avalanche energy mj t j operating junction and t stg storage temperature range soldering temperature, for 10 seconds (1.6mm from case) mounting torque, 6-32 or m3 screw 760 mj 1360 see fig. 14, 15, 24a, 24b 375 10lbf in (1.1n m) c a 300 -55 to + 175 20 2.5 max. 409 289 1524 195

automotive grade

base part number package type orderable part number form quantit y AUIRFB8409 to-220 tube 50 AUIRFB8409 auirfs8409 d2-pak tube 50 auirfs8409 auirfs8409 d2-pak tape and reel left 800 auirfs8409trl auirfsl8409 to-262 tube 50 auirfsl8409 standard pack
auirfb/s/sl8409

calculated continuous current based on maximum allowable junction temperature. bond wire current limit is 195a. note that current limitations arising from heating of the device leads may occur with some lead mounting arrangements.
repetitive rating; pulse width limited by max. junction temperature. limited by t jmax , starting t j = 25c, l = 0.15mh, r g = 50 ? , i as = 100a, v gs =10v. part not recommended for use above this value. i sd 100a, di/dt 990a/s, v dd v (br)dss , t j 175c. pulse width 400s; duty cycle 2%. c oss eff. (tr) is a fixed capacitance that gives the same charging time as c oss while v ds is rising from 0 to 80% v dss . c oss eff. (er) is a fixed capacitance that gives the same energy as c oss while v ds is rising from 0 to 80% v dss . when mounted on 1" square pcb (fr-4 or g-10 material). for recommended footprint and soldering techniques refer to application note #an-994.
jc !"# s d g static @ t j = 25c (unless otherwise specified) symbol parameter min. typ. max. units v ( br ) dss drain-to-source breakdown voltage 40 ??? ??? v ? v ( br ) dss / ? t j breakdown voltage temp. coefficient ??? 0.014 ??? v/c r ds(on) smd ??? 0.97 1.2 r ds(on) to-220 ??? 1.0 1.3 v gs ( th ) gate threshold voltage 2.2 ??? 3.9 v i dss drain-to-source leakage current ??? ??? 1.0 ??? ??? 150 i gss gate-to-source forward leakage ??? ??? 100 gate-to-source reverse leakage ??? ??? -100 r g internal gate resistance ??? 2.1 ??? ? dynamic @ t j = 25c (unless otherwise specified) symbol parameter min. typ. max. units gfs forward transconductance 150 ??? ??? s q g total gate charge ??? 300 450 q gs gate-to-source charge ??? 77 ??? q gd gate-to-drain ("miller") charge ??? 98 ??? q sync total gate charge sync. (q g - q gd ) ??? 202 ??? t d ( on ) turn-on delay time ??? 32 ??? t r rise time ??? 105 ??? t d(off) turn-off delay time ??? 160 ??? t f fall time ??? 100 ??? c iss input capacitance ??? 14240 ??? c oss output capacitance ??? 2130 ??? c rss reverse transfer capacitance ??? 1460 ??? c oss eff. (er) effective output capacitance (energy related) ??? 2605 ??? c oss eff. (tr) effective output capacitance (time related) ??? 2920 ??? diode characteristics symbol parameter min. typ. max. units i s continuous source current (body diode) i sm pulsed source current (body diode) v sd diode forward voltage ??? 0.86 1.2 v dv/dt peak diode recovery ??? 2.7 ??? v/ns t rr reverse recovery time ??? 52 ??? t j = 25c v r = 34v, ??? 52 ??? t j = 125c i f = 100a q rr reverse recovery charge ??? 97 ??? t j = 25c di/dt = 100a/s ??? 97 ??? t j = 125c i rrm reverse recovery current ??? 2.3 ??? a t j = 25c t on forward turn-on time intrinsic turn-on time is negligible (turn-on is dominated by ls+ld) t j = 175c, i s = 100a, v ds = 40v v dd = 20v i d = 100a, v ds =0v, v gs = 10v t j = 25c, i s = 100a, v gs = 0v integral reverse p-n junction diode. v gs = 0v, v ds = 0v to 32v mosfet symbol showing the conditions v gs = 10v conditions v gs = 0v, i d = 250a reference to 25c, i d = 1.0ma v gs = 10v, i d = 100a v ds = v gs , i d = 250a v ds = 40v, v gs = 0v v ds = 40v, v gs = 0v, t j = 125c v ds =20v v gs = 0v v ds = 25v ? = 1.0 mhz v gs = 0v, v ds = 0v to 32v i d = 30a r g = 2.7 ? v gs = 10v a na nc ns pf conditions v ds = 10v, i d = 100a i d = 100a v gs = 20v v gs = -20v ns nc a ??? ??? ??? ??? 409 1576 static drain-to-source on-resistance m ? v gs = 10v, i d = 100a thermal resistance symbol parameter typ. max. units r jc junction-to-case ??? 0.40 c/w r cs case-to-sink, flat greased surface 0.50 ??? r ja junction-to-ambient (pcb mount) ??? 62
auirfb/s/sl8409

fig 1. typical output characteristics fig 3. typical transfer characteristics fig 4. normalized on-resistance vs. temperature fig 2. typical output characteristics fig 6. typical gate charge vs. gate-to-source voltage fig 5. typical capacitance vs. drain-to-source voltage 2 3 4 5 6 7 v gs , gate-to-source voltage (v) 1.0 10 100 1000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) t j = 25c t j = 175c v ds = 25v 60s pulse width -60 -40 -20 0 20 40 60 80 100 120 140 160 180 t j , junction temperature (c) 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 r d s ( o n ) , d r a i n - t o - s o u r c e o n r e s i s t a n c e ( n o r m a l i z e d ) i d = 100a v gs = 10v 1 10 100 v ds , drain-to-source voltage (v) 1000 10000 100000 c , c a p a c i t a n c e ( p f ) v gs = 0v, f = 1 mhz c iss = c gs + c gd , c ds shorted c rss = c gd c oss = c ds + c gd c oss c rss c iss 0.1 1 10 100 v ds , drain-to-source voltage (v) 1 10 100 1000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) vgs top 15v 10v 8.0v 7.0v 6.0v 5.5v 4.8v bottom 4.5v 60s pulse width tj = 25c 4.5v 0.1 1 10 100 v ds , drain-to-source voltage (v) 10 100 1000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) 4.5v 60s pulse width tj = 175c vgs top 15v 10v 8.0v 7.0v 6.0v 5.5v 4.8v bottom 4.5v 0 50 100 150 200 250 300 350 400 q g , total gate charge (nc) 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 v g s , g a t e - t o - s o u r c e v o l t a g e ( v ) v ds = 32v v ds = 20v i d = 100a
auirfb/s/sl8409

fig 8. maximum safe operating area fig 10. drain-to-source breakdown voltage fig 7. typical source-drain diode forward voltage fig 11. typical c oss stored energy fig 9. maximum drain current vs. case temperature fig 12. maximum avalanche energy vs. draincurrent 0.0 0.5 1.0 1.5 2.0 2.5 v sd , source-to-drain voltage (v) 0.1 1 10 100 1000 i s d , r e v e r s e d r a i n c u r r e n t ( a ) t j = 25c t j = 175c v gs = 0v -60 -40 -20 0 20 40 60 80 100 120 140 160 180 t j , temperature ( c ) 40 41 42 43 44 45 46 47 v ( b r ) d s s , d r a i n - t o - s o u r c e b r e a k d o w n v o l t a g e ( v ) id = 1.0ma 25 50 75 100 125 150 175 starting t j , junction temperature (c) 0 500 1000 1500 2000 2500 3000 3500 e a s , s i n g l e p u l s e a v a l a n c h e e n e r g y ( m j ) i d top 26a 52a bottom 100a 25 50 75 100 125 150 175 t c , case temperature (c) 0 100 200 300 400 500 i d , d r a i n c u r r e n t ( a ) limited by package 0.1 1 10 100 v ds , drain-tosource voltage (v) 0.1 1 10 100 1000 10000 i d , d r a i n - t o - s o u r c e c u r r e n t ( a ) tc = 25c tj = 175c single pulse 1msec 10msec operation in this area limited by r ds (on) 100sec dc limited by package 0 5 10 15 20 25 30 35 40 45 v ds, drain-to-source voltage (v) 0.0 0.5 1.0 1.5 2.0 2.5 e n e r g y ( j ) v ds = 0v to 32v
auirfb/s/sl8409

fig 13. maximum effective transient thermal impedance, junction-to-case fig 14. typical avalanche current vs.pulsewidth fig 15. maximum avalanche energy vs. temperature notes on repetitive avalanche curves , figures 14, 15 (for further info, see an-1005 at www.irf.com) 1. avalanche failures assumption: purely a thermal phenomenon and failure occurs at a temperature far in excess of t jmax . this is validated for every part type. 2. safe operation in avalanche is allowed as long ast jmax is not exceeded. 3. equation below based on circuit and waveforms shown in figures 24a, 24b. 4. p d (ave) = average power dissipation per single avalanche pulse. 5. bv = rated breakdown voltage (1.3 factor accounts for voltage increase during avalanche). 6. i av = allowable avalanche current. 7. ? t = allowable rise in junction temperature, not to exceed t jmax (assumed as 25c in figure 14, 15). t av = average time in avalanche. d = duty cycle in avalanche = t av f z thjc (d, t av ) = transient thermal resistance, see figures 13) p d (ave) = 1/2 ( 1.3bvi av ) = t/ z thjc i av = 2 t/ [1.3bvz th ] e as (ar) = p d (ave) t av 1.0e-06 1.0e-05 1.0e-04 1.0e-03 1.0e-02 1.0e-01 tav (sec) 1 10 100 1000 a v a l a n c h e c u r r e n t ( a ) allowed avalanche current vs avalanche pulsewidth, tav, assuming ? j = 25c and tstart = 150c. allowed avalanche current vs avalanche pulsewidth, tav, assuming ? tj = 150c and tstart =25c (single pulse) 25 50 75 100 125 150 175 starting t j , junction temperature (c) 0 100 200 300 400 500 600 700 800 e a r , a v a l a n c h e e n e r g y ( m j ) top single pulse bottom 1.0% duty cycle i d = 100a 1e-006 1e-005 0.0001 0.001 0.01 0.1 t 1 , rectangular pulse duration (sec) 0.0001 0.001 0.01 0.1 1 t h e r m a l r e s p o n s e ( z t h j c ) c / w 0.20 0.10 d = 0.50 0.02 0.01 0.05 single pulse ( thermal response ) notes: 1. duty factor d = t1/t2 2. peak tj = p dm x zthjc + tc
auirfb/s/sl8409

!
"
# $# fig 17. threshold voltage vs. temperature

%#
&'
"
# $#

!
"
# $#

%#
&'
"
# $# fig 16. on-resistance vs. gate voltage -75 -50 -25 0 25 50 75 100 125 150 175 t j , temperature ( c ) 1.0 1.5 2.0 2.5 3.0 3.5 4.0 v g s ( t h ) , g a t e t h r e s h o l d v o l t a g e ( v ) i d = 250a i d = 1.0ma i d = 1.0a 0 200 400 600 800 1000 di f /dt (a/s) 0 2 4 6 8 10 12 i r r m ( a ) i f = 60a v r = 34v t j = 25c t j = 125c 0 200 400 600 800 1000 di f /dt (a/s) 0 2 4 6 8 10 12 i r r m ( a ) i f = 100a v r = 34v t j = 25c t j = 125c 0 200 400 600 800 1000 di f /dt (a/s) 60 100 140 180 220 260 q r r ( n c ) i f = 100a v r = 34v t j = 25c t j = 125c 0 200 400 600 800 1000 di f /dt (a/s) 50 100 150 200 250 300 q r r ( n c ) i f = 60a v r = 34v t j = 25c t j = 125c 4 6 8 10 12 14 16 18 20 v gs, gate -to -source voltage (v) 0.0 2.0 4.0 6.0 r d s ( o n ) , d r a i n - t o - s o u r c e o n r e s i s t a n c e ( m ? ) i d = 100a t j = 25c t j = 125c
auirfb/s/sl8409

( fig 22. typical on-resistance vs. drain current 0 200 400 600 800 1000 1200 i d , drain current (a) 0.0 2.0 4.0 6.0 r d s ( o n ) , d r a i n - t o - s o u r c e o n r e s i s t a n c e ( m ? ) v gs = 5.5v v gs = 6.0v v gs = 7.0v v gs = 8.0v v gs =10v
auirfb/s/sl8409

) fig 25a. switching time test circuit fig 25b. switching time waveforms fig 24b. unclamped inductive waveforms fig 24a. unclamped inductive test circuit t p v (br)dss i as r g i as 0.01 ? t p d.u.t l v ds + - v dd driver a 15v 20v v gs fig 26a. gate charge test circuit fig 26b. gate charge waveform vds vgs id vgs(th) qgs1 qgs2 qgd qgodr fig 23. *+
,#

#$#
"
!
for n-channel hexfet
power mosfets

?

?
?

p.w. period di/dt diode recovery dv/dt ripple 5% body diode forward drop re-applied voltage reverse recovery current body diode forward current v gs =10v v dd i sd driver gate drive d.u.t. i sd waveform d.u.t. v ds waveform inductor curent d = p. w . period - $ %&$'()'*) - + - + + + - - - $ ? ?
!
"#"" ? $
%% ? "#""&#
d.u.t. v ds i d i g 3ma v gs .3 f 50k ? .2 f 12v current regulator same type as d.u.t. current sampling resistors + - v ds 90% 10% v gs t d(on) t r t d(off) t f $ '( 1 ) $
0.1 % $ *+ $ + - $ $
auirfb/s/sl8409

. note: for the most current drawing please refer to ir website at http://www.irf.com/package/

to-220ab packages are not recommended for surface mount application. /
# *
0! 1
/' ,
# 23
2 443
4+
4+ 3
!
/#
5
auirfb/s/sl8409

to-262 part marking information

/
# *
0! 1
/' !" ,
# 23
2 443
4+
4+ 3
!
/#
5 to-262 package outline dimensions are shown in millimeters (inches)
auirfb/s/sl8409

#
$%&'

#
$%&'

note: for the most current drawing please refer to ir website at http://www.irf.com/package/ ! ,
# 23
2 443
4+
4+ 3
!
/#5 *
0! 1
/' /
#
auirfb/s/sl8409

#

( )
dimensions are shown in millimeters (inches) 3 4 4 trr feed direction 1.85 (.073) 1.65 (.065) 1.60 (.063) 1.50 (.059) 4.10 (.161) 3.90 (.153) trl feed direction 10.90 (.429) 10.70 (.421) 16.10 (.634) 15.90 (.626) 1.75 (.069) 1.25 (.049) 11.60 (.457) 11.40 (.449) 15.42 (.609) 15.22 (.601) 4.72 (.136) 4.52 (.178) 24.30 (.957) 23.90 (.941) 0.368 (.0145) 0.342 (.0135) 1.60 (.063) 1.50 (.059) 13.50 (.532) 12.80 (.504) 330.00 (14.173) max. 27.40 (1.079) 23.90 (.941) 60.00 (2.362) min. 30.40 (1.197) max. 26.40 (1.039) 24.40 (.961) notes : 1. comforms to eia-418. 2. controlling dimension: millimeter. 3. dimension measured @ hub. 4. includes flange distortion @ outer edge.
auirfb/s/sl8409

6
7!
"##"

1
!#

8"
1
"9
&$$ $ 66
:'&"
""'
' qualification information ? d 2 pak msl1 to- 220 to- 262 charged device model class c5 (+/- 2000v) ?? aec-q101-005 qualification level automotive (per aec-q101) comments: this part number(s) passed automotive qualification. ir?s industrial and consumer qualification level is granted by extension of the higher automotive level. n/a rohs compliant yes esd machine model class m4 (+/- 600v) ?? aec-q101-002 human body model class h3a (+/- 6000v) ?? aec-q101-001
auirfb/s/sl8409

unless specifically designated for the automotive market, international rectifier corporation and its subsidiaries (ir) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. part numbers designated with the ?au? prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. all products are sold subject to ir?s terms and conditions of sale supplied at the time of order acknowledgment. ir warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with ir?s standard warranty. testing and other quality control techniques are used to the extent ir deems necessary to support this warranty. except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. ir assumes no liability for applications assistance or customer product design. customers are responsible for their products and applications using ir components. to minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards. reproduction of ir information in ir data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. reproduction of this information with alterati ons is an unfair and deceptive business practice. ir is not responsible or liable for such altered documentation. information of third parties may be subject to additional restrictions. resale of ir products or serviced with statements different from or beyond the parameters stated by ir for that product or serv ice voids all express and any implied warranties for the associated ir product or service and is an unfair and deceptive business practice. ir is not responsible or liable for any such statements. ir products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the ir product could create a situation where personal injury or death may occur. should buyer purchase or use ir products for any such unintended or unauthorized application, buyer shall indemnify and hold international rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthori zed use, even if such claim alleges that ir was negligent regarding the design or manufacture of the product. only products certified as military grade by the defense logistics agency (dla) of the us department of defense, are designed and manufactured to meet dla military specifications required by certain military, aerospace or other applications. buyers acknowledge and agree that any use of ir products not certified by dla as military-grade, in applications requiring military gr ade products, is solely at the buyer?s own risk and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. ir products are neither designed nor intended for use in automotive applications or environments unless the specific ir product s are designated by ir as compliant with iso/ts 16949 requirements and bear a part number including the designation ?au?. buyers acknowledge and agree that, if they use any non-designated products in automotive applications, ir will not be responsible for any failure to meet such requirements. for technical support, please contact ir?s technical assistance center http://www.irf.com/technical-info/ world headquarters: 101 n. sepulveda blvd., el segundo, california 90245 tel: (310) 252-7105

▲Up To Search▲

Price & Availability of AUIRFB8409

	To Download AUIRFB8409 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .